Application range These vacuum pumps with vanes are mainly used in agriculture for filling and emptying slurry tanks, Benefits As B.P. pumps are tested, inspected and packaged with the utmost care, trouble-free start-up is 100% guaranteed, Nominal volume flow rate 6150 l/min, Drive type PTO 540 rpm, Direction of rotation Counter-clockwise (CCW), Ballast air injection system No, Lubrication system type Forced, Vane type Standard, Crash protection system No, Max vacuum 0.9 BAR, Max. relative pressure 1.5 BAR, Power requirement for max. pressure 21 kW, Power requirement for max. vacuum 11 kW, Diameter of hose connection 60 mm, Safety valve connection diameter 1-1/2 Inch, NTotal length 623 mm, Total width 410 mm, OHeight 637 mm, MMounting holes diameter 15 mm, Mounting holes to shaft end distance 304 mm, Mounting holes to end distance 95 mm, KShaft centre to left side end distance 195 mm, XShaft centre to right side end distance 215 mm, JShaft centre to bottom distance 95 mm, Shaft diameter 1-3/8 Inch, Max. shaft rotation 600 r/min, Weight 130 kg, Additional info *Please note that this item is either a dangerous good or a non-standard delivery size. This means a specialist carrier will be used and this item will take upto 48 hours to deliver. 28 1
Part numberMEC5000M EANUnitEach DetailsEach pump is subjected to a final check in the factory, in which the vacuum, compression and lubrication are tested, among other factors A test report relating to the serial number is drawn up for each pump Application rangeThese vacuum pumps with vanes are mainly used in agriculture for filling and emptying slurry tanks PropertiesThese pumps can generate both positive pressure and vacuum Oil to be used for lubricating the vanes: genuine oil from B. P. Item number: BP5070 Technical infoComposition of the item numbers: MEC = series, 8000 = type, M = indirect drive 540 rpm, A = automatic lubrication On pumps without automatic lubrication (no "A" in the item number), the pump is equipped with a forced lubrication system that is adjusted using dripper nozzles On pumps without automatic lubrication, the quantity of lubrication oil is set in the factory and cannot be changed without a tool In the case of forced lubrication, as with automatic lubrication, the function must be checked at all times during operation Pumps with indirect drive (M) must be driven anti-clockwise The direction of rotation is determined when the axle to be driven is aligned with the observer If the pump has a direct drive (for example, by a tractor unit) it must be driven anti-clockwise BenefitsAs B.P. pumps are tested, inspected and packaged with the utmost care, trouble-free start-up is 100% guaranteed Nominal volume flow rate6150 l/minDrive typePTO 540 rpm Direction of rotationCounter-clockwise (CCW) Ballast air injection systemNo Consists ofThese pumps are supplied with standard vanes ("Long-life" vanes available on request) Without pressure relief valve and vacuum valve The pumps are delivered without lubrication oil (BP5070) Including PTO shaft cover Lubrication system typeForced Vane typeStandard Crash protection systemNo Max vacuum0.9 BARMax. relative pressure1.5 BARPower requirement for max. pressure21 kWPower requirement for max. vacuum11 kWDDiameter of hose connection60 mmSafety valve connection diameter1-1/2 InchNTotal length623 mmBTotal width410 mmOHeight637 mmMMounting holes diameter15 mmIMounting holes distance227 mm189 mmEMounting holes to shaft end distance304 mmGMounting holes to end distance95 mmKShaft centre to left side end distance195 mmXShaft centre to right side end distance215 mmJShaft centre to bottom distance95 mmShaft diameter1-3/8 InchMax. shaft rotation600 r/minWeight130 kgAdditional info*Please note that this item is either a dangerous good or a non-standard delivery size. This means a specialist carrier will be used and this item will take upto 48 hours to deliver.
|
.png){kind=logo}
