Application range These vacuum pumps with vanes are mainly used in agriculture for filling and emptying slurry tanks, Properties These pumps can generate both positive pressure and vacuum, Nominal volume flow rate 13845 l/min, Drive type Hydraulic, Direction of rotation Clockwise (CW), Ballast air injection system No, Lubrication system type Forced, Vane type Long life, Crash protection system Yes, Max vacuum 0.95 BAR, Max. relative pressure 1.5 BAR, Power requirement for max. pressure 36 kW, Power requirement for max. vacuum 24 kW, Hydraulic motor required capacity 125 l/min, D,PDiameter of hose connection 100 mm, Safety valve connection diameter 2 Inch, Depression valve connection diameter 1-1/2 Inch, Total length 738 mm, OTotal width 390 mm, Height 575 mm, Mounting holes diameter 22 mm, Mounting holes to shaft end distance 299 mm, Mounting holes to end distance 192 mm, MShaft centre to left side end distance 195 mm, NShaft centre to right side end distance 195 mm, IShaft centre to bottom distance 164 mm, Max. shaft rotation 1400 r/min, Reservoir capacity 3.5 l, Weight 173 kg 29 1
Part numberMEC13500H EANUnitEach DetailsThe MEC II-series pumps have an automatic protection system. So, for example, if a vane breaks, the rotor and rotor housing can be protected by the rotor—including the flange mountings—being pushed downwards Pumps with a "ballast system", identified by B at the end of the item number (e.g. MEC9000MB) have a longer operating time in vacuum operation The operating time at -0.95 bar lasts from 8 minutes (standard) up to a maximum of 15 minutes. Continuous operation is permissible at -0.6 bar. MEC II-series pumps are supplied with long-life (heat-resistant) vanes as standard MEC II-series pumps feature a temperature meter to enable the temperature to be read during operation A maintenance hatch can be used to determine the wear condition of the vanes, indicating when the vanes need to be replaced Each pump is subjected to a final check in the factory, in which the vacuum, compression and lubrication are tested, among other factors A test report relating to the serial number is drawn up for each pump Application rangeThese vacuum pumps with vanes are mainly used in agriculture for filling and emptying slurry tanks PropertiesThese pumps can generate both positive pressure and vacuum Technical infoComposition of the item numbers: MEC = series, 9000 = type, H = hydraulic drive, B = ballast system On pumps without automatic lubrication (no "A" in the item number), the pump is equipped with a forced lubrication system that is adjusted using dripper nozzles Automatic lubrication available on request On pumps without automatic lubrication, the quantity of lubrication oil is set in the factory and cannot be changed without a tool In the case of forced lubrication, as with automatic lubrication, the function must be checked at all times during operation Pumps with hydraulic drive are clockwise The direction of rotation is determined when the axle to be driven is aligned with the observer Oil to be used for lubricating the vanes: genuine oil from B. P. (item number BP5070) BenefitsMinimum repair costs thanks to the unique automatic protection system As pumps from B.P. are tested, inspected and packaged with the utmost care, trouble-free start-up is 100% guaranteed Nominal volume flow rate13845 l/minDrive typeHydraulic Direction of rotationClockwise (CW) Ballast air injection systemNo Consists ofWithout pressure relief valve (item 0200013) and vacuum valve (item 0155513) Without hydraulic motor and key bush The pumps are delivered without lubrication oil (item BP5070) Including hydraulic base for mounting the hydraulic motor Lubrication system typeForced Vane typeLong life Crash protection systemYes Max vacuum0.95 BARMax. relative pressure1.5 BARPower requirement for max. pressure36 kWPower requirement for max. vacuum24 kWHydraulic motor required capacity125 l/minD,PDiameter of hose connection100 mmSafety valve connection diameter2 InchDepression valve connection diameter1-1/2 InchETotal length738 mmOTotal width390 mmGHeight575 mmFMounting holes diameter22 mmB,LMounting holes distance247 mm246 mmAMounting holes to shaft end distance299 mmCMounting holes to end distance192 mmMShaft centre to left side end distance195 mmNShaft centre to right side end distance195 mmIShaft centre to bottom distance164 mmMax. shaft rotation1400 r/minReservoir capacity3.5 lWeight173 kg
|
.png){kind=logo}
