Application range These vacuum pumps with vanes are mainly used in agriculture for filling and emptying slurry tanks, Properties These pumps can generate both positive pressure and vacuum, Benefits As B.P. pumps are tested, inspected and packaged with the utmost care, trouble-free start-up is 100% guaranteed, Nominal volume flow rate 8100 l/min, Drive type Hydraulic, Direction of rotation Clockwise (CW), Ballast air injection system No, Lubrication system type Forced, Vane type Standard, Crash protection system No, Max vacuum 0.9 BAR, Max. relative pressure 1.5 BAR, Power requirement for max. pressure 22 kW, Power requirement for max. vacuum 15 kW, Hydraulic motor required capacity 63.5 l/min, Diameter of hose connection 80 mm, Safety valve connection diameter 1-1/2 Inch, Total length 735 mm, Total width 410 mm, Height 597 mm, HMounting holes diameter 15 mm, Mounting holes to shaft end distance 287 mm, Mounting holes to end distance 196 mm, KShaft centre to left side end distance 195 mm, XShaft centre to right side end distance 215 mm, LShaft centre to bottom distance 164 mm, Max. shaft rotation 1400 r/min, Weight 153 kg, Additional info *Please note that this item is either a dangerous good or a non-standard delivery size. This means a specialist carrier will be used and this item will take upto 48 hours to deliver. 29 1
Part numberMEC8000H EANUnitEach DetailsEach pump is subjected to a final check in the factory, in which the vacuum, compression and lubrication are tested, among other factors A test report relating to the serial number is drawn up for each pump Application rangeThese vacuum pumps with vanes are mainly used in agriculture for filling and emptying slurry tanks PropertiesThese pumps can generate both positive pressure and vacuum Technical infoComposition of the part numbers: MEC = series, 8000 = type, H = hydraulic drive On pumps without automatic lubrication (no "A" in the item number), the pump is equipped with a forced lubrication system that is adjusted using dripper nozzles Automatic lubrication available on request On pumps without automatic lubrication, the quantity of lubrication oil is set in the factory and cannot be changed without a tool In the case of forced lubrication, as with automatic lubrication, the function must be checked at all times during operation Hydraulically driven pumps rotate clockwise. Anti-clockwise rotation available on request The direction of rotation is determined when the axle to be driven is aligned with the observer Oil to be used for lubricating the vanes: genuine oil from B. P. (item number BP5070) BenefitsAs B.P. pumps are tested, inspected and packaged with the utmost care, trouble-free start-up is 100% guaranteed Nominal volume flow rate8100 l/minDrive typeHydraulic Direction of rotationClockwise (CW) Ballast air injection systemNo Consists ofThese pumps are supplied with standard vanes. Long-life vanes available on request Without pressure relief valve and vacuum valve The pumps are delivered without lubrication oil (item BP5070) Including hydraulic base for mounting the hydraulic motor Without hydraulic motor and key bush Lubrication system typeForced Vane typeStandard Crash protection systemNo Max vacuum0.9 BARMax. relative pressure1.5 BARPower requirement for max. pressure22 kWPower requirement for max. vacuum15 kWHydraulic motor required capacity63.5 l/minDDiameter of hose connection80 mmSafety valve connection diameter1-1/2 InchATotal length735 mmBTotal width410 mmCHeight597 mmHMounting holes diameter15 mmIMounting holes distance227 mm252 mmEMounting holes to shaft end distance287 mmGMounting holes to end distance196 mmKShaft centre to left side end distance195 mmXShaft centre to right side end distance215 mmLShaft centre to bottom distance164 mmMax. shaft rotation1400 r/minWeight153 kgAdditional info*Please note that this item is either a dangerous good or a non-standard delivery size. This means a specialist carrier will be used and this item will take upto 48 hours to deliver.
|